Product Description
HangZhou Haige-Bar Peeling Machine
http://haigechina
Main Technical Parameters:
Model:WXC130S
| material requirement | diameter range (mm) | 35 |
| material length (mm) | ≥2800 | |
| yield strength(Mpa) | ≤1100 | |
| surface hardness | ≤HB320 | |
| straightness (mm/m) | ≤1.5 | |
| diameter tolerance | according to GB 702-2004 second group | |
| roundness(mm) | ≤50% of diameter tolerance | |
| surface roughness(Ra) | ≤25~50μm | |
| finished product | diameter range(mm) | 35≤dia≤130 |
| diameter cutting depth(mm) | 1.0~5.0 | |
| diameter tolerance | ≤h9 | |
| surface roughness (Ra) | ≤3.2μm | |
| feeding speed (m/min) | 0.3~6 | |
| cutting head rotation rate per minute(rpm) | 240~670 | |
| main motor(kw) | 110 | |
| total capacity(kw) | 140 | |
| compressed air (prepared by user) | 0.5~0.8MPa,1.8m3/min,0.8 m3 up air tank with 2 stage oil water separator and compressed air freezing type drying machine | |
Video Link:http://haigechina
Composition of Peeling Machine:
The equipment is usually composed of main machine and the table bed.
1.Main machine
consists of bed,spindle, air/oil lubrication system,front-clamping feeding system,rear-clamping extracting system,front CZPT and middle-rear CZPT system,etc.
2.Table bed
consists of the loader and unloader.
3.The air/oil lubrication system
The air/oil lubrication system is specially designed to lubricate and cool the spindle bearings during their highspeedrotation. It is composed of pump, oil and air distribution block and air source processing unit.
4.Cutting fluid circulation cooling system
Cutting fluid circulation cooling system consists of circulating water pump, pipeline, nozzle,etc.The cooled cutting liquid is taken by the water pump from reservoir to the nozzle nearthe cutter head through pipeline and sprays on the tools and scraps. Thus it takes away the cutting heat and drops into chip mouth with the scraps under the cutter head and flows back to the reservoir through the pipeline to be cooled again.
5.Chip conveyor
Chip conveyor is provided by our outsourcing supplier. The scraps falls CZPT the chain plate through the chip mouth under the cutter head and they are taken out by transmission and collected intensively.
6.Hydraulic system
consists of motor pumps, control valves, hydraulic oil tank, hydraulic pipeline etc.Clamping and loosening bars are realized through the cylinders in the front-clamping feeding and rear-clamping extracting systems.
7.The electrical system
The electrical system includes power supply system and controlling system, integrated by 1 power distribution cabinet and 1 button station,realizing the electric control of the main transmission, front- clamping feeding system, rear- clamping extracting system,cooling system, hydraulic system, conveyor and the table bed.
Company profile
HangZhou Haige Machine Tools Co.,Ltd was built in 1999,which specializes in producing steel finishing equipment,such as series WXC Centerless Lathe(Bar Peeling Machine),Series JY Bar Straightening Machine,Abrasive Belt Grinder(Belt Sander Polishing Machine),Drawing Machine,Shot Blasting Machine,Centerless Grinding Machine,CNC Skiving and Roller Burnishing Machine and Auxiliary Machine etc.We also engage in plating equipment and heat treatment equipment.
Based on 15 years manufacture and design experience,our machines have been exported to Russia,Vietnam,India,Pakistan,South Korea,North Korea,ZheJiang Province and other countries and regions.
Factory real landscape:
Processing Machinery
Accessories Area
Administrative Area
We regard customer’s satisfaction as our unremitting pursuit.
Packaging Show
Packaging Detail:
The first layer
wrapping with foam film and stretch film for the special components, in order to avoid moisture.
Second layer
inside of plywood box, adopting small square plywood block and strapping belt to fix.
Third layer
the machine itself has screw fixing holes, so it can be tightly fixed on the bottom of the plywood box through screw and nut.
Fourth layer
in a container, by compact layout, reducing the gap between boxes to avoid shaking. At the same time, reinforcing between the bottom of the container and plywood boxes once again, furthermore using hanging steel wire protection.
Outside wooden case with export fumigation.
About Our Service:
A.Warranty period:1 year except for fast-wearing parts.
B.Immediate response when get informed of machine problem.
C.The machine operators of buyer’s can be trained in our factory for free.
D.Provide long term free technical support.
E.If necessary,we can dispatch our well-trained and professional engineers to our customer’s factories to help them with the machine installation and commissioning.
F.Customized design is available.OEM&ODM are welcomed.
Application:
Bright steels,Non-ferrous metals such as copper,titanium,magnesium,aluminum,Fasteners,
Auto parts,Springs,Hydraulics,Bearings,Machining.
FAQ
Q&A
1.Are you manufacturer or trading company?
We are professional manufacturer and we have more than 10 years experience in this field.We have our own factory.
Besides,at the end of 2014,we was just estabilished a trading company.
2.How many employees are there in your factory?
Approximately 150 persons.
3.Do you have your own R&D team?How many design engineers do you have?
Yes,we have our own R&D team.More than 10 persons.
4.Which countries have your machines been exported to now?
Russia,South Korea,North KOrea,Pakistan,India,Vietnam,ZheJiang ,etc.
We regard our customer’s satisfaction as our unremitting pursuit.
Contact Information:
buy drive chain
Buying a drive chain requires a certain understading of its characteristics. This article discusses the different types of chains available, including Silent, Flat-top, and Duplex. By the end of this article, you should have a basic understanding of what each type of chain is for. First, here are some basic rules to keep in mind when shopping for a chain. To find the drive chain that best suits your needs, read on.
roller chain
Choosing the right roller chain for your drive chain depends on several factors. First, you have to determine the motor horsepower and rpm for the small drive sprocket. These values determine the size of the chain and the number of teeth on the drive sprocket. Next, you need to determine the size of the conveyor chain, it can be the horizontal, vertical, or curved radius. Depending on your specific needs, you can also choose between two-strand or three-strand chains.
The roller chain of the drive chain must be properly tensioned. It should also have a proper lubrication system. Chain sag should not exceed 2 to 4 percent of the center distance (the distance between the 2 axles). Also, it shouldn’t make any unusual noises or obvious problems. One of the main reasons for excessive wear is the size of the load. Each chain has a specified maximum working load.
The maximum roller chain load must be less than 1/9 or 6 times the tensile strength of the drive chain. This amount should not exceed this threshold, as exceeding this level will result in chain plate fatigue. To avoid this, you should use a roller chain with a higher number of strands. Also, for high power requirements, a roller chain with a higher number of strands is recommended. One final tip for choosing a drive chain: it should not be used when there is a high risk of corrosion or rusting.
The materials used to manufacture roller chains vary according to the specific application. Common materials include steel and stainless steel. However, stainless steel is used in food processing machinery and other environments that require lubrication. Brass and nylon are also sometimes used. These factors determine the selection of suitable materials for the drive chain. If you are not sure which material to use, you can consult an industry professional. These professionals will help you choose the right chain for the job at hand.
mute chain
The design of the silent transmission chain is as follows: the large chain plates 2 are stacked 1 on top of the other in the direction of the chain length. The connecting rods are connected by connecting pins 3. The outermost and central guide plates 4 are fastened to the connecting pins 3 by means of rivets. This construction helps minimize friction on the sliding surfaces of the chain. Chainplate 2 of the silent transmission chain is usually made of stainless steel.
The link plates are made of steel and have a rectangular shape with pinholes 41. These guide plates have no teeth but have curved surfaces that guide the silent drive chain on the sprockets. In addition, the rear portion of the guide plate is higher than the portion of the chainplate. This feature improves pitch balance. The present invention is also applicable to silent transmission chains using rockers.
When it comes to chain design, it’s important to remember that silent drive chains are often used in automotive engines, especially timing and cam drives. This type of drive reduces noise and vibration due to its low engagement angle and links engagement with the sprocket. However, these applications are not limited to timing and cam drives; they can also be used for front-wheel power transmission. For example, silent drive chains are designed to resemble those used in NASCAR racing engines.
The design of the silent drive chain is based on the structure of the roller chain. Its components are standardized and manufactured according to pitch. There are single-row and multi-row versions. Quiet chains, also known as inverted tooth chains, are shaped to reduce noise from stretching. It’s also designed to minimize the amount of friction caused by small changes in pitch. Its teeth don’t slide against each other, so the chain is smoother and more durable.
flat top chain
One of the important parts of the flat top chainplate system is the hinge pin, which is used to fix the chainplate and is responsible for the smooth and efficient conveying of the chainplate. There are several types of hinge pins, including single hinge pins and double hinge pins. The single hinge pin is suitable for the chainplate with a small span and small bearing capacity, and the double hinge pin is suitable for the chainplate with a large span and high bearing capacity.
The side bending flat top chain is suitable for conveying large and medium workpiece pallets. They can be made of steel or plastic, each with its own advantages. Both chainplates are designed to convey material smoothly. Side curved flat-top chains can be used on straight conveyors. They have a low coefficient of friction and can transport weights up to 1.2 kg/cm. They can also be combined with HD profiles.
Flat top drive chains are usually made of plastic material and come in 2 types: tabletop chains and buffer chains. They come in a variety of widths, but the most popular are standard widths, ranging from 3.25 inches to 12 inches. MatTop chains are usually shipped in 10-foot lengths. They come in different styles, but they all have the same basic specs. Tabletop chains are designed for general conveying, while pad chains are used for specific applications. Solid top chains are suitable for conveying bulk materials, while wide pad chains can handle large volumes of fluids and/or solid-solid mixtures.
These chain conveyors can be used to convey, connect or lift small items. This type of chain is especially useful in industries where the product is hot or greasy. The modular design of these chains allows them to be configured in 3 dimensions, making them suitable for production changes and transitions. They also help reduce slack in the chain. Flat top chains are commonly used in final assembly and mechanical or paint restoration in the automotive industry.
double chain
Besides the roller chain, another type of chain drive is the double drive chain. This type of chain consists of a series of short cylindrical rollers connected together by side links and driven by gears called sprockets. This type of chain is very reliable and only requires a tractor with a high rpm PTO. It is manufactured by CZPT and is available in many different sizes and finishes.
Self-lubricating chain
Self-lubricating drive chains are the ideal solution for applications that do not require the relubrication of conventional chains. This maintenance-free roller chain features fully heat-treated components that increase the chain’s fatigue resistance and strength. It’s sintered alloy bushings are oil-impregnated, reducing the chance of premature wear and elongation. Its self-lubricating properties enhance its durability and work well even in hard-to-reach places.
CZPT self-lubricating roller chains feature preloaded sintered steel bearing pins and oil-impregnated sintered bushings. These chains are drop-in replacements for standard roller chains and run on the same sprockets as standard chains. In addition to being maintenance-free, self-lubricating roller chains are compatible with most existing sprockets and are ideal for demanding applications.
The O-ring chain concept was used to develop self-lubricating systems. It has 2 or more annular grease storage chambers. A self-lubricating bushing roller chain has an oil reservoir between its pin chain and the roller chainplate. A grease seal between these 2 plates isolates the moving parts and keeps the joints well lubricated. O-rings are made of special nitrile rubber, whose properties vary by application.
CZPT SLR conveyor chains and CZPT SLR drive chains have rollers on sintered bushings. CZPT SLR chains and SLR conveyor chains are self-lubricating and have a higher working load than standard ANSI chains. They may not be interchangeable with other self-lubricating chains from other manufacturers. Self-lubricating drive chains are the best solution for demanding industrial applications requiring heavy-duty, reliable conveying.
